Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Cost in Hollis?
Garage door repair in Hollis typically costs $150-$600, and most common repairs land near the lower half of that range. A single spring replacement runs $180-$340, an opener repair $120-$320, and a full new door installation $700-$2200. Those are typical estimated ranges for the Hollis market, and the written estimate you get after a technician looks at the door sets the final price.
We handle the full spread of work: springs, cables, openers, panels, tracks, rollers, and complete installs. If your door won’t open or won’t stay closed, call (877) 492-2281. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Most garage door repairs in Hollis fall between $150 and $600.
- Spring repair is priced per spring: $180-$340 for one, roughly double for a matched pair.
- New door installation runs $700-$2200 depending on door size, material, and insulation.
- Estimates are free, and the written estimate is the price.
- Emergency calls are handled as a core service, not an upsell. We answer 24/7.
Garage Door Cost Breakdown (2026)
Here’s how the individual jobs usually price out in Hollis. These are typical estimated ranges, not quotes. The written estimate after we see the door is what you pay.
| Service | Typical Estimated Cost |
|---|---|
| Garage door repair (general) | $150-$600 |
| Spring repair (one spring) | $180-$340 |
| Cable repair | $130-$250 |
| Opener repair | $120-$320 |
| Opener installation | $250-$550 |
| Panel replacement | $250-$500 |
| Track realignment | $120-$240 |
| Roller replacement | $110-$220 |
| New door installation | $700-$2200 |
A few notes on the table. Spring pricing is for one spring. Springs usually fail in matched pairs, and when one breaks the other is typically near the end of its life, so a pair costs about twice the single-spring range. We tell you which situation you’re in before any work starts. Opener repair sits at the low end when it’s a logic board reset or a sensor alignment and climbs toward $320 when a motor or gear assembly needs replacement. Panel replacement depends on whether the panel is a stock profile or a discontinued one, since matching an older door’s color and stamping can take longer.
Track realignment and roller replacement are the small jobs that get skipped, and skipping them is what turns a cheap fix into an expensive one. A bent track grinds the rollers, the rollers wear the hinges, and the door starts straining the opener. Catching it at $120-$240 beats replacing an opener later.
What Affects Garage Door Pricing in Hollis
Two doors in the same Hollis block can price differently, and it’s rarely about the door itself. Here’s what moves the number.
- Door size and material. A single-car door in steel is the least expensive path. Double-wide doors, insulated doors, and wood or wood-composite faces from Clopay, Amarr, Wayne Dalton, or Raynor all sit higher in the $700-$2200 installation range because of panel cost and weight.
- Spring type and count. Torsion springs cost more than extension springs, and a two-spring setup costs roughly double a single. Standard-lift doors use one spring configuration; high-lift and low-headroom setups use another. We confirm which you have before quoting.
- Opener brand and age. We’re certified on LiftMaster, Chamberlain, Genie, and Craftsman. A current-model opener with a bad sensor is a quick, inexpensive fix. An older unit where the parts are discontinued can push repair toward the top of the $120-$320 range, and at that point replacement in the $250-$550 range is sometimes the better spend.
- Condition of the surrounding hardware. A door that’s been out of alignment for a while usually needs tracks, rollers, and hinges addressed together. Bundling that work into one visit costs less than three separate trips.
- Weather exposure. Hollis doors face real seasonal swings: humid summers, freezing winters, and the freeze-thaw cycling that comes with them. That cycling works on springs, cables, and the seals at the bottom of the door. A door that’s binding in January often traced back to hardware that was already worn by the previous summer. We look at the whole system, not just the part that made the noise.
- Whether the door is repairable at all. A single dented panel is a $250-$500 fix. A door with a cracked center stile, rusted-through bottom sections, and a bent track is usually a replacement conversation. We’ll tell you plainly which side of that line you’re on.
How to Save on Garage Door Repair in Hollis
The biggest savings come from catching problems early and from not paying twice for the same visit.
- Get the free estimate before authorizing anything. Call (877) 492-2281 and we’ll price the job in writing. There’s no charge for the estimate, and the written number is what the job costs.
- Fix the small stuff before it cascades. Roller replacement at $110-$220 and track realignment at $120-$240 are cheap compared to the opener and panel damage that misalignment causes over a season.
- Replace springs in pairs when the first one fails. It’s more upfront than a single spring, but the second spring on a matched set usually fails soon after the first, and you’d pay for a second service visit.
- Ask whether repair or replacement makes more sense. On a door past its useful life, putting $400 into hardware on a door that needs $2000 of replacement work anyway is money wasted. We’ll say so if that’s the case.
- Bundle related work into one appointment. If the door needs rollers, a cable, and an opener adjustment, doing it in one visit is cheaper than three.
When Does a Repair Cost More Than a Replacement?
As a rough rule, if the repair estimate climbs past roughly half the cost of a new door, replacement usually wins on total cost over the next several years. On a door in the $700-$2200 installation range, a repair quote approaching the low four figures is the signal to talk about replacement instead. The other signals are structural: a bent or rusted-through track that can’t be straightened, a cracked center stile, or multiple failed panels on a door whose profile is discontinued. Cosmetic damage alone rarely justifies a new door.
Ask us to price both options on the same visit. It’s the only honest way to compare, and it costs you nothing.
What Happens When You Call
You reach a person, not a queue. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
When a technician arrives, the first job is diagnosis. Springs, cables, opener logic, track alignment, and panel condition all get checked, including the parts you didn’t call about. You get a written estimate before any work begins, and you approve it before we touch the door. If the door is trapping a car or leaving the house open, say so when you call and we’ll treat it as the emergency it is. Emergency garage door service is a core part of what we do, not an add-on.
Why Brand Matters on a Pricing Page
We’re certified to work on eight major brands: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. That matters for cost because brand knowledge is what keeps a diagnosis from turning into guesswork. A Genie opener with a specific symptom has a known set of causes. A Clopay door panel has a known profile and a known lead time. When the technician already knows the equipment, you’re not paying for exploratory visits.
It also means we can service the opener and the door under one call. Openers from LiftMaster, Chamberlain, Genie, and Craftsman and door panels from Clopay, Amarr, Wayne Dalton, and Raynor are all within what we handle. Springs, openers, panels, full installs: one call covers it all. You can read more about our full range of work on our garage door repair East New York page.
Safety: What We Won’t Talk You Through
Torsion springs and the cables that run with them are under extreme tension, and the tools needed to release that tension safely aren’t in a typical homeowner’s garage. We don’t walk customers through spring or cable work over the phone, and we’d rather you didn’t attempt it. The same goes for anything involving the opener’s wiring at the wall or ceiling. A trained technician with the right winding bars and the right experience handles it. Our technicians have up to 15 years of experience, and spring work is one of the jobs that experience matters most for. The local pro we connect you with is licensed and insured as their state requires.
FAQs – Garage Door Cost in Hollis
How much does garage door repair cost in Hollis?
Garage door repair in Hollis typically costs $150-$600 depending on the part and the extent of the damage. Spring repair runs $180-$340 for one spring, cable repair $130-$250, and opener repair $120-$320. Call (877) 492-2281 for an exact quote. Estimates are free.
Is it cheaper to repair or replace a garage door?
Repair is usually cheaper when the door’s panels and frame are structurally sound and the problem is hardware: springs, cables, rollers, tracks, or the opener. Replacement in the $700-$2200 range makes more sense when the door has cracked structural members, rusted-through sections, or multiple failed panels. A repair estimate approaching half the cost of a new door is the usual tipping point. Call (877) 492-2281 and we’ll price both so you can compare.
How much does a new garage door cost in Hollis?
A new garage door installation in Hollis typically runs $700-$2200. A single-car steel door sits at the low end; a double-wide insulated door or a wood-composite face from Clopay, Amarr, Wayne Dalton, or Raynor sits higher. Opener installation, if you need one, adds $250-$550. Call (877) 492-2281 for a written estimate on your specific door.
Why does one spring cost less than a pair?
Because a single torsion or extension spring runs $180-$340, and springs are usually replaced in matched pairs, so a pair costs about twice that. The two springs on a door wear at the same rate, so when one breaks the other is typically close behind. Replacing both at once avoids a second service call weeks later. Call (877) 492-2281 and we’ll tell you which setup your door has.
Can you come today?
Same-day service is often possible, and emergency calls are treated as a priority. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (877) 492-2281 and tell us what the door is doing.
Get a Free Estimate on Your Hollis Garage Door
Whether it’s a snapped spring, an opener that’s stopped responding, or a door you’ve outgrown and want replaced, the fastest way to a real number is a call. We work on LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor equipment, and we handle repair, spring work, opener diagnostics, and full installation under one roof. Call (877) 492-2281 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The written estimate sets the final price, and there’s no charge to get it.
Pricing reflects the Hollis market as of 2026. Garage Door Repair East New York offers free estimates. Call (877) 492-2281.
Written by the team at Garage Door Repair East New York.
What Our Customers Say
"Logic board on a 15 year old opener. He was upfront that a new opener would cost less than the board plus labor, and he wasn't wrong. No pressure either way."
- Karen Kim"Replaced the bottom panel after I backed into it. Color match is close enough that you have to know to look for it."
- Jason Mercer"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Nia Ellison